add this to accel conf and reload daemon

After that you can use - accel-cmd show sessions

but with this i will load daemon when check every 1 min

to get connected user and put to database

i see PostgreSQL but is not options in installation use mysql/mariadb

is easy options to put this information to fail when user connect to put all information ifname,username,ip,type,state,calling-sid,rx-bytes,tx-bytes,uptime

if i use accel-cmd

is will load daemon

if i write small demon to check every second for new record when new user is connect

in log i see : [2020-10-09 00:53:32]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:32]: debug: cli: disconnect
[2020-10-09 00:53:32]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:32]: debug: cli: disconnect
[2020-10-09 00:53:32]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:32]: debug: cli: disconnect
[2020-10-09 00:53:32]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:32]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:33]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:33]: debug: cli: disconnect
[2020-10-09 00:53:34]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:34]: debug: cli: disconnect
[2020-10-09 00:53:34]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:34]: debug: cli: disconnect
[2020-10-09 00:53:34]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:34]: debug: cli: disconnect
[2020-10-09 00:53:34]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:34]: debug: cli: disconnect
[2020-10-09 00:53:34]:  info: cli: tcp: new connection from 127.0.0.1
[2020-10-09 00:53:34]: debug: cli: disconnect

when i disable debug will have only in log

is the problem log will go over gigabyte for 1 hour

is easy to disable log but connection will got to daemon and will load accel may be

after clear all verbose and check for other debug

in log show

[2020-10-09 01:12:51]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:52]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect
[2020-10-09 01:12:53]: debug: cli: disconnect

accel-cmd show sessions |grep neshto si

kakwo po tochno ti trqbva

kude se izgubi

?